Print | Rate this content

HP Jetdirect 600N EIO Internal Print Servers - Product Specifications

Figure 1: HP 600n

The HP Jetdirect 600N (EIO Internal Print Server) provides a network connection for the new HP peripherals equipped with an enhanced I/O (EIO) interface slot. The HP Jetdirect 600N EIO cards have 2 MB of upgradeable Flash memory and perform at two times the speed of MIO HP Jetdirect cards.

Model numbers

J3110A, J3111A, J3112A, J3113A

top

Configurations and models

Configurations
Model Number
HP Jetdirect 600N EIO Internal Print Server for Ethernet/10Base-T networks
J3110A
HP Jetdirect 600N EIO Internal Print Server for Ethernet/10Base-T and 10Base2 and LocalTalk networks
J3111A
HP Jetdirect 600N EIO Internal Printer Server for Token Ring networks
J3112A
HP Jetdirect 600N EIO Internal Print Server for Ethernet/10/100Base-TX networks
J3113A

top

Product overview

Supported protocols

Supported Network Protocols
Supported Networks
600N Product Model
IPX/SPX
Novell IntranetWare Novell NetWare
J3110A J3111A J3112A J3113A
IPX/SPX-compatible
Microsoft (R) Windows 95 Microsoft Windows NT
J3110A J3111A J3112A J3113A
EtherTalk
AppleTalk
J3110A J3111A J3113A
LocalTalk
AppleTalk
J3111A
DLC/LLC
IBM LAN Server Microsoft LAN Manager Microsoft Windows for Workgroups Microsoft Windows NT Artisoft LANtastic*
J3110A J3111A J3112A J3113A
TCP/IP
Windows XP, 2000, NT lpd UNIX (R), including: Hewlett-Packard HP-UX, Sun Microsystems SunOS/Solaris (Sun SPARCsystems only), SCO UNIX**, IBM AIX**, HP MPE-iX**
NOTE: * Refer to the HP Jetdirect product data sheets for supported network versions. For other networks, consult your system vendor or authorized HP dealer.

** Contact your network system vendor for software, documentation, and support.

Windows 95, 98, Me
J3110A J3111A J3112A J3113A

Electrical characteristics

1.25 A maximum at 3.3 V nominal

Environmental operating conditions

Operating
Non-Operating
Temperature
0 to 55 degrees C (32 to 131 degrees F)
-40 to 70 degrees C (-40 to 158 degrees F)
Relative Humidity (non-condensing)
15 to 95% at 40 degrees C (104 degrees F)
15 to 90 percent at 65 degrees C (149 degrees F)
Maximum Altitude
4.6 km (15,000 feet)
4.6 km (15,000 feet)

Port configuration

Model
Port Configuration
J3110A
Ethernet, IEEE 802.3 Type 10Base-T (RJ-45)
J3111A
Ethernet, IEEE 802.3 Type 10Base-T (RJ-45), Type 10Base2 (BNC), and LocalTalk (Mini-DIN 8)
J3112A
Token Ring/IEEE 802.5 (RJ-45 or DB-9)
J3113A
Fast Ethernet, IEEE 802.3 Type 10Base-T or IEEE 802.3u Type 100Base-TX (RJ-45)

Product bundles

One HP Jetdirect card with one HP Jetadmin CD.

Recommended cables and requirements

Model
Port Configuration
J3110A
10Base-T unshielded twisted pair cabling
J3111A
10Base-T unshielded twisted pair cabling, 10Base2 thin coaxial cabling, or 8-pin mini-DIN (LocalTalk)
J3112A
Type 1, 2, or 6 shielded cabling (Token Ring) or shielded and unshielded twisted pair cabling (RJ-45)
J3113A
10/100Base-TX unshielded twisted pair cabling

Setting the jumpers on the J3113A to 10/100 link speed

Link configuration jumpers (P1, P2, and P3) can be used to configure the print server. These jumpers should be used if the print server is unable to establish a network link through autonegotiation. If P1 is changed to the AUTO=OFF position, then P2 selects the link speed (10 or 100 Mbps) and P3 selects the communication mode (Half duplex or Full duplex). If you manually configure the print server using jumpers P2 and P3, you must match the configuration of the connecting device, such as the network hub or switch.

Figure 2: Jumper Locations and Labels

1 - 1- This Jumper is Labeled Auto
2 - 2- This Jumper is Labeled 100
3 - 3- This Jumper is Labeled H

In the table below, the "0" 's mark the position of the exposed pins and the "X" 's mark the position of the jumpers, one jumper over two pins.

Setting
Label
P1
Label
P2
Label
P3
AUTO=ON (Default)*
Auto
X X O
100
X X O
H
X X O
100 Mbps Half-Duplex (AUTO=OFF)
Auto
O X X
100
X X O
H
X X O
100 Mbps Full-Duplex (AUTO=OFF)
Auto
O X X
100
X X O
H
O X X
10 Mbps Half-Duplex (AUTO=OFF)
Auto
O X X
100
O X X
H
X X O
10 Mbps Full-Duplex (AUTO=OFF)
Auto
O X X
100
O X X
H
O X X

Manual part numbers

Product
Language
Part Number
HP Jetdirect Interface Manual Kit
English
5063-2111
HP Jetdirect Hardware Installation Guide
5967-0854
HP Jetdirect Software Installation Guide
5966-5171
HP Jetdirect CD-ROM Installation Booklet
English French Italian German Spanish
5966-5248
HP CD-ROM Installation Booklet
Chinese Korean Japanese Simplified Chinese
5967-0823
Data Sheet
5966-0084E
HP Jetdirect Connectivity Guide
5966-0083E

Pre-installed software

No pre-installed software; each card comes bundled with HP Jetadmin software on CD.

top

Warranty

  • One-year return to HP

  • Standard Delivery Unit Exchange

top

Energy Star compliance

None

top

Regulatory compliance

  • FCC Class A for HP J3112A Token Ring, and for HP J3110A/J3111A/J3113A Ethernet or IEEE 802.3/802.3u

  • FCC Class B for HP J3111A with LocalTalk Only

top

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!