|| Rate this content|
Product Specifications HP Designjet 750C Printer
Serial number location
When looking at the front of the printer, the serial number is located directly above the power cord on the left-rear panel.
The HP DesignJet 750C printer is a large-format, color and monochrome, inkjet printer that provides hardcopy output of computer program data.
Large-format plots of high resolution and quality are generated for applications such as:
The printer accepts drawing data from CAD software programs supporting the following languages:
The printer supports HP-GL/2 with both the Roman and the Japanese Kanji character sets (provided the Kanji ROM SIMM is fitted). PostScript (TM) is also available when the PostScript upgrade is fitted.
Cable restrictions for the printer are determined by the type of interface being used. Recommendations for each interface are supplied in the following paragraphs.
The use of a short cables (each less than 15 meters or 50 feet) is recommended for the RS-232-C interface. A longer cable is permissible, provided the load capacitance does not exceed 2500 picofarads.
The use of a short cable (less than 2 meters or 6.6 ft.) is recommended for the Centronics interface.
C3195A = D/A1-size printer.
C3196A = E/A0-size printer.
NOTE: See also Supplies Source catalog and (in Europe and USA) Media Reference Guide. From time to time, new media types may become available. For up-to-date information, please contact your HP dealer or local HP Sales and Support Office.
NOTE: *Except for glossy media types, on which the resolution is always 300 dpi.
The printers handle sheet media and roll media. Supported standard sizes are as follows:
The printers handle media that does not exceed the following maximum and minimum:
Black Inkjet print cartridge
Color Inkjet print cartridge
The HP DesignJet 750C printer has four (4) megabytes (MB) of standard on-board RAM, plus three (3) additional MB used internally. A PostScript ROM and an MIO card are optional. There are also two RAM-expansion sockets, which can hold an optional 4 MB, 8 MB, 16 MB, or 32 MB, single in-line memory module (SIMM). The maximum RAM is therefore 68 + 3 MB.
The HP DesignJet 755CM printer has 4 MB of standard on-board RAM, plus 3 additional MB used internally. In addition, the PostScript ROM SIMM, the MIO card, and two 32-MB SIMMs are pre-installed in the standard configuration.
"Normal" printer use
"Normal" printer use means less than:
If your drawings are smaller than E/A0, the number of pages per day could be higher.
If you use the printer less than this, it is unlikely you will need to get it serviced. If you use the printer more than this, it is possible that, after a period of time, it will need to be serviced. The printer itself keeps an internal count of total pages printed and total passes of the print cartridges. If the front panel periodically displays STATUS: Maintenance advised. This means that your use of the printer has exceeded one of the following:
Contact your local HP dealer or HP service engineer to arrange service. After the service, the message will disappear. If you choose to ignore the message, you may continue to use the printer as normal, but may encounter a number of operational or print-quality problems.
You can see the current count of the two statistics on the Service Configuration Plot.
To print the Service Configuration Plot
One-year on-site hardware warranty
Except when purchased as part of a system, HP warrants your graphics peripheral hardware product against defects in materials and workmanship for a period of one year from receipt by the end user (proof of purchase required). If HP receives notice of such defects during the warranty period, HP will either, at its option, repair or replace products that prove to be defective.
Should HP be unable to repair or replace the product within a reasonable amount of time, the customer's alternative exclusive remedy shall be refund of the purchase price upon return of the product.
If this product was purchased as part of an HP system in a coordinated shipment or as a system add-on, it is warranted against defects in material and workmanship during the same period as the HP system.