Print | Rate this content

HP Color LaserJet 2600n Printer - Configuration Options for the HP Color LaserJet 2600n Toolbox

The HP Color LaserJet 2600n Toolbox is divided into two main sections: the HP Color LaserJet2600n Toolbox section and the Device Settings section. Each of these sections has controls grouped into a set of tabs. In addition to these two sections, the HP Color LaserJet 2600n Toolbox has other pages that are accessible from various points within the HP Color LaserJet 2600n Toolbox. The following lists describe the basic layout of these sections and the configuration options available on each tab.

This document provides information about the following topics:

  • HP Color LaserJet 2600n Toolbox section

  • Device Settings section

  • Other pages

HP Color LaserJet 2600n Toolbox section

The HP Color LaserJet 2600n Toolbox section is comprised of the following tabs.

  • Status tab

  • Troubleshooting tab

  • Alerts tab

  • Documentation tab

Status tab

The Status tab contains the following pages.

  • Device Status page

  • Supplies Status page

  • Print Info Pages page

Device Status page

The Device Status page shows device status messages from the device. The Device Status page also displays some pertinent printer information and device settings.

Figure 1: Device Status page (1 of 2)

Figure 2: Device Status page (2 of 2)

Status messages

The status messages that appear on the Device Status page are the same messages that appear on the HP Color LaserJet 2600n control panel display. The following message types are available:

  • Initialization and Ready messages

  • Supplies messages

  • Alert messages

  • Warning messages

  • Critical error messages

  • Status messages

  • Printing reports and documents messages

Initialization and Ready messages

The following table lists the available status/control panel initialization and Ready messages for the HP Color LaserJet 2600n printer.

Control Panel Initialization and Ready Messages
Message
Description
Hewlett Packard
Power on
Permanent storage init.
NVRAM initialization (power on with SELECT and CANCEL buttons pressed and held)
Intitializing . . .
Print engine warming up
Ready
Idle with no other pending messages
Supplies messages

The following table lists the available status/control panel supplies messages for the HP Color LaserJet 2600n printer.

Control Panel Supplies Messages
Message
Description
Replace cyan cartridge
alternates with
Single supply is out (gas gauge for depleted supply flashes).
Replace magenta cartridge
alternates with
Replace yellow cartridge
alternates with
Replace black cartridge
alternates with
Replace supplies
alternates with
Multiple supplies are out
Install cyan cartridge
alternates with
Single supply is not installed (identified by "?" character)
Install magenta cartridge
alternates with
Install yellow cartridge
alternates with
Install black cartridge
alternates with
Install supplies
alternates with
Multiple supplies are not installed (identified by "?" characters)
10.xxxx supply error
alternates with
Reinstall
Supply error for a specific cartridge. Identified by "?" character.
The list of 10.xxxx errors appear below:
  • 10.0000 Black cartridge e-label error
  • 10.0001 Cyan cartridge e-label error
  • 10.0002 Magenta cartridge e-label error
  • 10.0003 Yellow cartridge e-label error
  • 10.1000 Black e-label missing
  • 10.1001 Cyan e-label missing
  • 10.1002 Magenta e-label missing
  • 10.1003 Yellow e-label missing
Incorrect black
Black cartridge incorrectly installed
Incorrect cyan
Cyan cartridge incorrectly installed
Incorrect magenta
Magenta cartridge incorrectly installed
Incorrect yellow
Yellow cartridge incorrectly installed
Incorrect supplies
Multiple cartridges incorrectly installed
Non HP cyan installed
alternates with
To accept press
A non-HP supply is detected (cloned or refilled).
This is a continuable error state. The user must acknowledge the message by pressing the SELECT button.
Non HP magenta installed
alternates with
To accept press
Non HP yellow installed
alternates with
To accept press
Non HP black installed
alternates with
To accept press
Unauthorized black
alternates with
To accept press
An unauthorized supply is detected (misuse of HP in OEM e-label field). A "misuse of HP in OEM E-label field" error is essentially a non-HP cartridge message.
This is a continuable error state. The user must acknowledge the message by pressing the SELECT button.
Unauthorized cyan
alternates with
To accept press
Unauthorized magenta
alternates with
To accept press
Unauthorized yellow
alternates with
To accept press
Non HP supply in use
alternates with
Ready
A non-HP supply has been overridden (cloned or refilled supply).
This message is a Ready State with Warning error; it does not require the user to take action.
Unauthorized supply in use
alternates with
Ready
An unauthorized supply was overridden (misuse of HP in OEM field). A "misuse of HP in OEM E-label field" error is essentially a non-HP cartridge message.
This message is a Ready State with Warning error; it does not require the user to take action.
HP supplies installed
alternates with
Ready
The printer has transitioned from having one or more non-HP supplies to having none. This message displays for 5 seconds and then returns to Ready state.
This message is a Ready State with Warning error; it does not require the user to take action.
Order black cartridge
alternates with
Ready
A supply is low.
This message is a Ready State with Warning error; it does not require the user to take action.
Order cyan cartridge
alternates with
Ready
Order magenta cartridge
alternates with
Ready
Order yellow cartridge
alternates with
Ready
Order supplies
alternates with
Ready
Multiple supplies are low.
This message is a Ready State with Warning error; it does not require the user to take action.
Replace supply. Override in use
alternates with
Ready
Supply override in use. The user has decided to continue printing beyond the out point.
Replace supplies. Override in use
alternates with
Ready
Alert messages

The following table lists the available status/control panel alert messages for the HP Color LaserJet 2600n printer.

Control Panel Alert Messages
Message
Description
Load Tray 1<Type><Size>
alternates with
Press to use available media
Printer is processing job, but no trays match. The option is to use existing tray settings.
Load Tray #<Type><Size>
alternates with
Press to use available media
Printer is processing job, but a matching tray is empty.
Load paper
Out of paper in all available trays
Manual feed Press
alternates with
Load Tray 1<Type><Size>
Printer manual feed mode
Load Tray # Press
Manual duplex - # is the tray from which the first half of the print job was printed.
Misprint Press
Feed delay misprint
Unexpected size in tray #
alternates with
Load[Size]
Unexpected size error
No paper pickup Press
Print paper tray mispick
Memory is low Press
Job processing memory low. User must acknowledge the error.
Door open
Door open
Jam in tray 2
alternates with
Clear jam and press
Paper jam in tray 2
Jam in tray 3
alternates with
Clear jam and press
Paper jam in tray 3
Jam in print paper path
alternates with
Open door and clear jam
Paper jam in registration area - drum area
Jam in cartridge area
alternates with
Open door and clear jam
Paper jam in drum area - fuser area
Jam in output bin
alternates with
Open door and clear jam
Paper jam in fuser area - output paper area
Jam in print paper path
alternates with
Open door and clear jam
Paper jam in duplex feeding area
Jam in output bin
alternates with
Open door and clear jam
Paper jam in duplex reversing area
Warning messages

The following table lists the available status/control panel warning messages for the HP Color LaserJet 2600n printer.

Control Panel Warning Messages
Message
Description
Device error Press
BD glitch
Engine comm. error
Print Engine Communication error
Engine error Press
Beam detect malfunction
Critical error messages

The following table lists the available status/control panel critical error messages for the HP Color LaserJet 2600n printer.

Control Panel Critical Error Messages
Message
Description
50.1 Fuser Error Turn off then on
50.1 Low fuser error
50.2 Fuser Error Turn off then on
50.2 Slow fuser error
50.3 Fuser Error Turn off then on
50.3 High fuser error
50.4 Fuser Error Turn off then on
50.4 Fuser driver error
50.6 Fuser Error Turn off then on
50.6 Fuser open error
50.8 Fuser Error Turn off then on
50.8 Low subthermistor fuser error
50.9 Fuser Error Turn off then on
50.9 High subthermistor fuser error
51.20 Error Turn off then on
Black laser scanner error
51.21 Error Turn off then on
Cyan laser scanner error
51.22 Error Turn off then on
Magenta laser scanner error
51.23 Error Turn off then on
Yellow laser scanner error
57 Fan Error Turn off then on
Fan error
55.1 Error Turn off then on
55.1 DC controller error
59.4 Error Turn off then on
59.4 Abnormal fuser motor rotation
59.A0 Error Turn off then on
59.A0 ETB motor rotation error
59.9 Error Turn off then on
59.9 ETB motor start error
59.C0 Error Turn off then on
59.C0 Developer motor rotation error
54.1C Error Turn off then on
Density sensor contaminator warning or CPR sensor contamination
Sensor Error Turn off then on
Toner level or TOP sensor errors
Status messages

The following table lists the available status/control panel status messages for the HP Color LaserJet 2600n printer.

Control Panel Status Messages
Message
Description
Calibrating...
Calibrating
Cleaning...
Cleaning
Loading tray 1 Plain, <Size>
alternates with
Clean Mode to start
Cleaning mode paper prompt
Printing reports and documents messages

The following table lists the available status/control panel printing reports and documents messages for the HP Color LaserJet 2600n printer.

Control Panel Printing Reports and Documents Messages
Message
Description
Printing report:[Report name]
Printing an internal report
Canceling report
Canceling report
Printing document
Printing
Canceling print
Canceling print

Supplies Status page

The Supplies Status page displays the status of all of the supplies used by the printer, including the black, cyan, magenta, and yellow print cartridges and the imaging drum. This page also provides a link for return and recycling information.

Figure 3: Supplies Status page (1 of 2)

Figure 4: Supplies Status page (2 of 2)

Print Info Pages page

The Print Info Pages page provides users the ability to easily print out the internal special pages that are generated by the device. The following information pages are available.

  • Configuration page

  • Supplies page

  • Menu structure

  • Demo page

  • Color print sample

Figure 5: Print Information Pages page

top

Troubleshooting tab

The pages listed under the Troubleshooting tab consist of static HTML content outlining troubleshooting procedures. The Troubleshooting tab contains the following pages.

  • Clearing Jams page

  • Print Problems page

  • Troubleshooting Tools page

  • Animated Demonstrations page

Clearing Jams page

Use this section to help troubleshoot paper jams that might occur on the HP Color LaserJet 2600n printer.

Figure 6: Clearing Jams page

This page contains a link to static HTML content about clearing paper jams, as well as a ShockwaveFlash animation about clearing paper jams.

Print Problems page

Use this section to help identify and find solutions for image quality, media handling, and performance problems that might occur on the HP Color LaserJet 2600n printer.

Figure 7: Print Problems page

This page contains a link to static HTML content about basic print quality problems.

Troubleshooting Tools page

Clicking the Troubleshooting Tools link on the left navigation bar opens the Print Quality Troubleshooting Tools page. Use the information on this page to troubleshoot print quality issues.

Figure 8: Troubleshooting Tools page (1 of 2)

Figure 9: Troubleshooting Tools page (2 of 2)

The Print Quality Troubleshooting Tools page contains links to the following troubleshooting tools.

  • Troubleshooting Checklist . This link goes to HTML content that contains the basic troubleshooting checklist.

  • Print Quality Troubleshooting Page . A link in this section allows the user to view the Print Quality Troubleshooting Procedure. Clicking Print sends the Print Quality Troubleshooting Procedure page to the printer.

  • Cleaning Page . This section goes through the cleaning process including Print and Clean buttons to print and use the cleaning page.

  • Calibration . Clicking Calibrate Now initiates a calibration session on the HP Color LaserJet 2600n printer.

Print Quality Troubleshooting Procedure page

Clicking Click here to open the Print Quality Troubleshooting Procedure page on the Troubleshooting Tools page opens the Print Quality Troubleshooting Procedure page.

Figure 10: Print Quality Troubleshooting Procedure page (1 of 2)

Figure 11: Print Quality Troubleshooting Procedure page (2 of 2)

This page provides information about how to use the Print Quality Troubleshooting Procedure and also provides links to other helpful pages within the HP Color LaserJet 2600n Toolbox.

Animated Demonstrations page

Figure 12: Animated Demonstrations page

The links on this page go to Shockwave Flash animations of the following procedures:

  • Replacing a print cartridge

  • Paper jam removal

  • Manual duplex printing (printing on both sides of the paper)

top

Alerts tab

The Alerts tab contains the Alerts page.

Alerts page

This page allows the user to set up the status alerts for the HP Color LaserJet 2600n printer. The following table shows the available alerts for the HP Color LaserJet 2600n printer.

Alerts
Event Log Codes
Config Pg Codes
Instant Support XML Codes
Alert Text
Control Panel Message
Load Paper [TYPE][TRAY]
None
The HP Color LaserJet 2600n is out of paper. Please load YY¹ into Tray X²
Load Paper
Manual Feed
None
Load the necessary paper in the specified tray, OR, if usable paper is already in the specified tray, press the SELECT button at the device.
Manual feed Press (SELECT )
Door Cover Open
None
The printer door is open. The door must be closed before printing can continue.
Door open
Tray 2 Jam
13.0000
A paper jam has occurred in Tray 2. Clear the jam, and then press the SELECT button at the device.
Jam in tray 2
Tray 3 Jam
13.0000
A paper jam has occurred in Tray 3. Clear the jam, and then press the SELECT button at the device.
Jam in tray 3
Jam in Drum area
13.0000
A paper jam has occurred in the print path. Open the door, and clear the jam. Then press the SELECT button at the device.
Jam in print paper path
Jam in Drum Fuser area
13.0000
A paper jam has occurred in the print path. Open the door, and clear the jam. Then press the SELECT button at the device.
Jam in Cartridge area
Jam in Fuser output
13.0000
A paper jam has occurred in the output area. Clear the jam. And then press the SELECT button at the device.
Jam in output bin
Printer Mispick
None
A paper mispick has occurred. Check that paper is loaded correctly, then press the SELECT button at the device.
No paper pickup Press (SELECT
Fuser Warmup Fail
50.2000 Slow Fuser
50.2 FUSER ERROR. To continue, turn the device off. Ensure the fuser is fully seated, then turn the device on.
Note: 50.2 Slow fuser error
Message: 50.2 Fuser Error Turn off then on
Fuser Low Temp Fail
50.1000
50.1 FUSER ERROR. To continue, turn the device off. Ensure the fuser is fully seated, then turn the device on.
50.1 Fuser Error Turn off then on
Fuser Hi Temp Fail
50.3000
50.3 FUSER ERROR. To continue, turn the device off. Ensure the fuser is fully seated, then turn the device on.
50.3 Fuser Error Turn off then on
Scanner Yellow Laser fail
51.2300
YELLOW SCANNER ERROR. To continue, turn the device off then on.
51.23 Error Turn off then on
Scanner Magenta Laser fail
51.2200
MAGENTA SCANNER ERROR. To continue, turn the device off then on.
51.22 Error Turn off then on
Scanner Cyan Laser fail
51.2100
CYAN SCANNER ERROR. To continue, turn the device off then on.
51.22 Error Turn off then on
Scanner Black Laser fail
51.2000
BLACK SCANNER ERROR. To continue, turn the device off then on.
51.20 Error Turn off then on
Fan Error
57.0000
FAN ERROR. To continue, turn the device off then on.
57 Fan Error Turn off then on
Engine Comm Error
55.0000
ENGINE COMMUNICATION ERROR. To continue, turn the device off then on.
Engine comm. Error
Misprint
MISPRINT
The printed page has been incorrectly placed on the paper. To continue, press the SELECT button at the device.
Misprint Press (SELECT
DC Controller Error
55.1000
55.1 PRINTER ERROR. To continue, turn the device off then on.
55.1 Error Turn off then on
Order Black Cartridge
None
The Black Cartridge low threshold has been reached. For more information, go to HP LaserJet 2600n toolbox and click Supplies Status . To order supplies online, click Order Supplies .
Alternates: Order black cartridge / Ready GAS GAUGE
Order Yellow Cartridge
None
The Yellow Cartridge low threshold has been reached. For more information, go to HP LaserJet 2600n toolbox and click Supplies Status . To order supplies online, click Order Supplies .
Alternates: Order yellow cartridge / Ready GAS GAUGE
Order Magenta Cartridge
None
The Magenta Cartridge low threshold has been reached. For more information, go to HP LaserJet 2600n toolbox and click Supplies Status . To order supplies online, click Order Supplies .
Alternates: Order magenta cartridge / Ready GAS GAUGE
Order Cyan Cartridge
None
The Cyan Cartridge low threshold has been reached. For more information, go to HP LaserJet 2600n toolbox and click Supplies Status . To order supplies online, click Order Supplies .
Alternates: Order cyan cartridge / Ready GAS GAUGE
Black Incorrect
None
INCORRECT BLACK CARTRIDGE. The cartridge is in the incorrect position.
Incorrect black
Black Missing
None
INSTALL BLACK CARTRIDGE. The print cartridge is missing.
Alternates message: 10.1000 Supply Error / Reinstall GAS GAUGE
Non-HP Black Cartridge
10.3000
NON-HP BLACK CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Non HP Black installed / To accept press (SELECT
Unauthorized Black Cartridge
10.3200
UNAUTHORIZED BLACK CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Unauthorized black / To accept press (SELECT
Replace Black
None
REPLACE BLACK CARTRIDGE. The out threshold has been reached. The supply must be replaced before printing can continue.
Replace black cartridge
Black E-label Error
10.0000
SUPPLY MEMORY ERROR ON BLACK. Unable to read the supply data. Re-install the supply. If the error reappears, contact support.
Alternates message: 10.0000 Supply Error / Reinstall GAS GAUGE
Cyan Incorrect
None
INCORRECT CYAN CARTRIDGE. The cartridge is in the incorrect position.
Incorrect cyan
Cyan Missing
None
INSTALL CYAN CARTRIDGE. The print cartridge is missing.
Alternates message: 10.1001 Supply Error / Reinstall GAS GAUGE
Non-HP Cyan Cartridge
10.3001
NON-HP CYAN CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Non HP cyan installed / To accept press (SELECT
Unauthorized Cyan Cartridge
10.3201
UNAUTHORIZED CYAN CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device
Alternates message: Unauthorized cyan / To accept press (SELECT
Replace Cyan
None
REPLACE CYAN CARTRIDGE. The out threshold has been reached. The supply must be replaced before printing can continue.
Replace cyan cartridge
Cyan E-label Error
10.0001
SUPPLY MEMORY ERROR ON CYAN. Unable to read the supply data. Re-install the supply. If the error reappears, contact support.
Alternates message: 10.0001 Supply Error / Reinstall GAS GAUGE
Magenta Incorrect
None
INCORRECT MAGENTA CARTRIDGE. The cartridge is in the incorrect position.
Incorrect Magenta
Magenta Missing
None
INSTALL MAGENTA CARTRIDGE. The print cartridge is missing.
Alternates message: 10.1002 Supply Error / Reinstall GAS GAUGE
Non-HP Magenta Cartridge
10.3002
NON-HP MAGENTA CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Non HP magenta installed / To accept press (SELECT
Unauthorized Magenta
10.3202
UNAUTHORIZED MAGENTA CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Unauthorized magenta / To accept press (SELECT
Replace Magenta
None
REPLACE MAGENTA CARTRIDGE. The out threshold has been reached. The supply must be replaced before printing can continue.
Replace magenta cartridge
Magenta E-label Error
10.0002
SUPPLY MEMORY ERROR ON MAGENTA. Unable to read the supply data. Re-install the supply. If the error reappears, contact support.
Alternates message: 10.0002 Supply Error / Reinstall GAS GAUGE
Yellow Incorrect
None
INCORRECT YELLOW CARTRIDGE. The cartridge is in the incorrect position.
Incorrect yellow
Yellow Missing
None
INSTALL YELLOW CARTRIDGE. The print cartridge is missing.
Alternates message: 10.1003 Supply Error / Reinstall GAS GAUGE
Non-HP Yellow Cartridge
10.3003
NON-HP YELLOW CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Non HP yellow installed / To accept press (SELECT
Unauthorized Yellow Cartridge
10.3203
UNAUTHORIZED YELLOW CARTRIDGE INSTALLED. Any printer repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. To use this cartridge, override by pressing the SELECT button at the device.
Alternates message: Unauthorized yellow / To accept press (SELECT
Replace Yellow
None
REPLACE YELLOW CARTRIDGE. The out threshold has been reached. The supply must be replaced before printing can continue.
Replace yellow cartridge
Yellow E-label Error
10.0003
SUPPLY MEMORY ERROR ON YELLOW. Unable to read the supply data. Re-install the supply. If the error reappears, contact support.
Alternates message: 10.0003 Supply Error / Reinstall GAS GAUGE
¹ YY stands for available paper types, such as Letter or Legal.

² X stands for available trays, such as Tray 2 or Try 3.

The following illustration shows a sample Status Alert.

Figure 13: Sample status alert window

Figure 14: Set up Status Alerts page

Clicking the Turn on alerts option button or the Turn off alerts option button, and then clicking Apply turns on or off the alerts that have been selected on this page and displays the Configuration Result page.

Figure 15: Configuration Results page

top

Documentation tab

The Documentation tab contains the following pages.

  • Print: How do I? page

  • Network: How do I? page

  • Other: How do I? page

  • User Guide page

  • Readme page

Print: How do I? page

This page provides links to information to help perform print tasks.

Figure 16: Print: How do I? page

Network: How do I? page

This page provides links to information to help perform network tasks.

Figure 17: Network: How do I? page

Other: How do I? page

This page provides links to information to help install print cartridges.

Figure 18: Other: How do I? page

User Guide page

Use this page to gain access to the user guide for the HP Color LaserJet 2600n printer.

Figure 19: User Guide page

Readme page

Use this page to gain access to the Readme for your HP Color LaserJet 2600n printer.

Figure 20: Readme page

top

top

Device Settings section

The Device Settings section is comprised of the following tabs.

  • Information tab

  • Settings tab

  • Network tab

Gain access to the Device Settings section of the HP Color LaserJet 2600n Toolbox by clicking the Device Settings button located at the top right corner of the Device Status page. When this method is used, the opening screen of the Device Settings section looks like the following illustration.

Figure 21: Accessing Device Settings through HP Color LaserJet 2600n Toolbox

If the HP Color LaserJet 2600n printer is installed through the on-board networking feature, you can also gain access to the Device Settings section by opening the Web browser and typing in the IP address of the HP Color LaserJet 2600n printer. When this method is used, also known as the Embedded Web Server, the opening screen of the Device Settings section looks like the following illustration.
NOTE: Print a Configuration page to locate the printer IP address.

Press the SELECT button on the printer control panel to enter the Main Menu to print a Configuration page. Press the SELECT button again to enter the Reports Menu, use the right or left arrow buttons to navigate to Config Report , and then press the SELECT button.

Figure 22: Accessing Device Settings by typing printer IP address

Information tab

NOTE: The Information tab appears only if access to the Device Settings page is gained by opening the Web browser and typing in the printer IP address. See Device Settings section for more information.

The Information tab contains the following pages.

  • Device Status page

  • Configuration page

  • Supplies Status page

  • Print Info pages

Device Status page

The Device Status page shows device status messages from the device. The Device Status page also displays some pertinent printer information and device settings.

Figure 23: Information Tab Device Status page (1 of 2)

Figure 24: Information Tab Device Status page (2 of 2)

For a list of the status messages that appear in HP Color LaserJet 2600n Toolbox, see Status messages section of this document for more information.

Configuration page

Use this page to change the advanced settings for your HP Color LaserJet 2600n printer.

The Configuration page displays the values of all of the settings available to be set in the printer. The contents of this page is consistent with the Configuration page generated by the firmware.

'The following sections are presented on this page.

  • Product Information section

  • Network Information section

  • Page Counts section

  • Print Settings section

  • Paper Options section

  • Print Density section

Figure 25: Configuration page (1 of 2)

Figure 26: Configuration page (2 of 2)

Supplies Status page

NOTE: The Supplies Status page displayed in the Device Settings section of the HP Color LaserJet 2600n Toolbox is identical to the Supplies Status page displayed in the HP Color LaserJet 2600n Toolbox section.

The Supplies Status page displays the status of all of the supplies used by the printer, including the black, cyan, magenta, and yellow print cartridges and the imaging drum. This page also provides a link for return and recycling information.

Figure 27: Supplies Status page (1 of 2)

Figure 28: Supplies Status page (2 of 2)

Print Info pages

NOTE: The Print Information Pages page displayed in the Device Settings section of the HP Color LaserJet 2600n Toolbox is identical to the Print Information Pages page displayed in the HP Color LaserJet 2600n Toolbox section.

Use this page to print the internal pages for the HP Color LaserJet 2600n. The following information pages are available.

  • Configuration page

  • Demo page

  • Supplies page

  • Menu structure page

Figure 29: Information tab - Print Information Pages page

Settings tab

The Settings tab contains the following pages.

  • Paper Handling page

  • Printing page

  • Print Quality page

  • Print Density page

  • Paper Type Settings page

  • Print Modes page

  • System Setup page

  • Service page

Paper Handling page

Use this page to configure the paper-handling settings for the HP Color LaserJet 2600n printer.

Figure 30: Paper Handling page

Printing page

Use this page to change the printing defaults for the HP Color LaserJet 2600n printer.

Figure 31: Printing page

Print Quality page

Use this page to change the print quality defaults for the HP Color LaserJet 2600n printer.

Figure 32: Print Quality page (1 of 2)

Figure 33: Print Quality page (2 of 2)

The following options are available from the Optimize menu.

Optimize option
Description
Background Toner
Decreased developer AC bias peak-to-peak voltage.
Extra Cleaning
Extended post-rotation time (by 2 to 11 seconds) plus fan speed up (for high-talc media).
Trailing Edge Over-development (full-speed)
Change blank pulse setting (number of AC bias saves that are dropped out).
Trailing Edge Over-development (half-speed)
Decreased developer AC bias peak-to-peak voltage.
Mottle prevention
Extended pre-rotation time (by 15 seconds).
Less Duplex Transfer Current
Decreased transfer bias on second side of duplex jobs. For media that has low resistivity after fusing.
More Duplex Transfer Current
Increase transfer bias on second side of duplex jobs. For media that has high resistivity after fusing.

Print Density page

Use this page to control the print density of each print cartridge on the HP Color LaserJet 2600n printer.

Figure 34: Print Density page (1 of 2)

Figure 35: Print Density page (2 of 2)

Paper Type Settings page

Use this page to set the default paper type settings for the HP Color LaserJet 2600n printer.

Figure 36: Paper Type Settings page

Print Modes page

Use this page to change the print mode for customizable paper types for the HP Color LaserJet 2600n printer.

Figure 37: Print Modes page (1 of 2)

Figure 38: Print Modes page (2 of 2)

Standard print modes
Standard Print Mode
Extended Print Mode
Color Tables
Sensor Correlation
Default Media Types
Normal Mode
none
Plain
Plain
Plain, Color, Preprinted, Prepunched, Recycled
Heavy Mode
none
Plain
Plain
Heavy
Cardstock Mode
More fusing
Plain
Plain
Cardstock, Bond
Cardstock Mode
none
Plain
Plain
HP Premium Cover
Light Mode
none
Plain
Plain
Light
Light Glossy Mode
Less fusing
Glossy
Light Glossy
Light Glossy
Glossy Mode
none
Glossy
Glossy
Glossy
Heavy Glossy Mode
none
Glossy
Glossy
Heavy Glossy
Heavy Glossy Mode
none
Glossy
Glossy
HP Premium Plus Photo
Tough Paper Mode
none
Glossy
Glossy
HP Tough Paper
Envelope Mode
none
Plain
Plain
Envelopes
Transparency Mode
none
OHT
Glossy
Transparency
Label Mode
none
Plain
Plain
Label
Extended print modes
Extended Print Modes
Description
Fusing
Less paper curl
Reduced fuser temperature for less paper curl
Heavy coverage
Increased fuser temperature for heavy toner coverage
Toner offset
Reduced fuser temperature for less toner offset
Flap sealing
Reduced fuser temperature to keep envelope flaps from sealing
Less fusing
Reduced fuser temperature
More fusing
Increased fuser temperature
Transfer
Dry paper
Increase transfer current for high resistivity paper
Humid paper
Decreased transfer bias for high resistivity paper
Rough paper
Increased transfer bias for high resistivity paper
Less transfer current
Reduced transfer bias
More transfer current
Increased transfer bias
Toner
Less toner
Tone curve is scaled back so that solid is not 100% halftone

System Setup page

Use this page to change settings on the HP Color LaserJet 2600n printer.

Figure 39: System Setup page

Service page

Use this page to begin the cleaning mode or to restore the factory settings for the HP Color LaserJet 2600n printer.

Figure 40: Service page

Network tab

The Network tab contains the following pages.

  • IP Configuration

  • Advanced page

  • mDNS page

  • SNMP page

  • Password page

IP Configuration

Use this page to configure the IP address and WINS address for the HP Color LaserJet 2600n printer.

Figure 41: IP Configuration page (1 of 2)

Figure 42: IP Configuration page (2 of 2)

Advanced page

Use this page to configure the enabled settings and other settings, such as link speed, for the HP Color LaserJet 2600n printer.

Figure 43: Advanced page

mDNS page

Use this page to configure the mDNS settings for the HP Color LaserJet 2600n printer.

Figure 44: mDNS page

SNMP page

Use this page to configure the SNMP settings for the HP Color LaserJet 2600n printer.

Figure 45: SNMP page

Password page

Use this page to set or change the Administrator password.

The following occurs when the user sets the password.

  • Only the Network tab and its contents are protected. A user is able to view and change configuration items on the Status and Settings tabs.

  • Once the user clicks the Networking tab, a pop-up dialogue box appears, into which the user must type in the correct password.

  • When the user types in a correct password, the customer can view and change any of the configuration items under the Networking tab.

  • A customer only needs to enter the password one time during a browser session. The user clicks the Networking tab and types in the password. The user can go back to the Status and Settings tabs. When the user clicks the Networking tab, the user does not need to enter the password again unless the user opens a new browser session.

Figure 46: Password page

top

Other pages

The following pages are also available through the HP Color LaserJet 2600n Toolbox.

  • About HP Color LaserJet 2600n Toolbox page

  • HP Instant Support page

  • Product Registration page

  • Order Supplies page

  • Product Support page

About HP Color LaserJet 2600n Toolbox page

This page contains information concerning the versions of the various HP Color LaserJet 2600n Toolbox components installed on the computer.

Figure 47: About Toolbox page

HP Instant Support page

Use this page to obtain instant support from HP.

Figure 48: HP Instant Support page

Product Registration page

The Product Registration link connects to a Web page to register the HP Color LaserJet 2600n printer.

Figure 49: Product Registration page

Order Supplies page

The Order Supplies link connects to a Web page that helps order supplies online from a reseller. The supplies needed for the HP Color LaserJet 2600n printer are pre-selected. The quantities can be changed or additional items can be selected. The items are dropped into the shopping cart, ready for checkout, ensuring that the correct supplies are ordered through the selected reseller.

Figure 50: Order Supplies page

Product Support page

The Product Support link connects to a Web page that helps get online support for the HP Color LaserJet 2600n printer.

top

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!