Print | Rate this content

HP LaserJet 1022 Series Printers - Windows Installation for Direct Connections

The HP LaserJet 1022 printing-system software can be used in the following configurations:

  • You install the HP LaserJet 1022 printing-system software on a computer that is directly connected to the product through a USB port. On Windows systems, you can share your HP LaserJet 1022 Series printer with other users on your network.

  • The HP LaserJet 1022 Series printer is directly connected to a computer and you install only the printer driver.

  • You install the HP LaserJet 1022 printing-system software on a computer that has access to a local area network (LAN). The HP LaserJet 1022n and HP LaserJet 1022nw printers connect to a LAN through an internal HP network port.

NOTE: HP recommends that you install the software before connecting the product to the computer (software-first installation). However, if the product is already connected to the computer, you can install the software by using the Plug-and-Play method or by using the Add Printer Wizard.

Supported Windows operating systems

Supported operating systems when installing the full software package

The following Windows operating systems are fully supported through the software installer and drivers available on the software CD that comes with the HP LaserJet 1022 Series printer:

NOTE: Windows 2000 Server is not supported. HP suggests using an alternate MS print driver such as an MS Windows HP LaserJet 6L or 5L print driver.
  • Microsoft ® Windows 98 SE

  • Microsoft Windows Millennium Edition (Windows Me)

  • Microsoft Windows 2000

  • Microsoft Windows XP (32-bit)

  • Microsoft Windows 2003

NOTE: Because the HP LaserJet 1022 series product models do not have a parallel port, they do not support MS-DOS, Windows 95, Windows 98 (first edition), or Windows NT. These operating systems require a parallel port and do not support USB connections.

top

Supported operating systems when installing only the printer driver

The following Windows operating system has print-driver-only support by the HP LaserJet 1022 printing-system software:

  • Microsoft Windows 2003 Server (32-bit) - print driver included on the printing-system CD

top

top

Windows system requirements

For print-driver-only support, the HP LaserJet 1022 printing-system software has the following minimum system requirements.

  • Processor and RAM requirements:

    • For Windows 98 SE and Windows ME: a computer with at least a Pentium® 166 MHz processor and 32 MB of RAM

    • For Windows 2000: a computer with at least a Pentium 166 MHz processor and 64 MB of RAM

    • For Windows XP: a computer with at least a Pentium 233 MHz processor and 128 MB of RAM

  • 150 MB or more of free hard-disk space

  • CD-ROM drive (required for installation)

  • Works with USB and Hi-Speed USB systems and cables

top

Windows installation for direct connections

Use the following instructions to install the product software on a computer that is running Windows 98 SE, Windows Me, Windows 2000, or Windows XP (32-bit only).

CAUTION: Set up and turn on the product before installing the printing-system software. Do not connect the product to the computer until the software installation program prompts you to do so.
NOTE: You must have administrator privileges to install the printing-system software on Windows 2000 or Windows XP.
  1. Close all of the programs that are open on the computer.

  2. Insert the HP LaserJet 1022 printing-system software CD into the CD-ROM drive.

    NOTE: If your CD does not start automatically, click Start, click Run, and then browse to and double-click the SETUP.EXE file in the root directory of the CD.
  3. Click Next and follow the onscreen prompts as follows:

    1. CD Browser screen

      Click Next, (Takes you to the Software License Agreement screen - Step b.).
      NOTE: Documentation. Click this link to launch your Web browser and go to the Hewlett-Packard LaserJet 1020 Series Products Software Readme File .
    2. HP Software License Agreement screen

      Click Yes. (Takes you to the Model dialog box - Step c.)

    3. Model Selection screen

      If you click HP LaserJet 1020or HP LaserJet 1022, Next takes you to the Start Copying Files dialog box (Step m).

      If you click HP LaserJet 1022n or HP LaserJet 1022nw, Next takes you to the Printer Connection dialog box (Step d).

    4. Printer Connection screen

      If you click Connected directly to this computer (a direct connection), Next causes the Installer to look for new hardware, and then takes you to the Start Copying Files dialog box (Step m).

      If you click Connected via the network or Connected via wireless, Next takes you to the Identify Printer dialog box (Step e).

      NOTE: The Connected via wireless option is available for the HP LaserJet 1022nw model only.
    5. Identify Printer screen

      NOTE: If you are installing a direct-connection to the printer, go to step m.

      Clicking the Search from a list of detected printers (recommended) option, and then clicking Next takes you to the Notice about Firewalls dialog box (Step f).

      Clicking the Specify a printer by address option, and then clicking Next takes you to the Specify Printer dialog box (Step l).

    6. Firewalls screen

      Click Next, (Takes you to the Printer Found dialog box - Step g.)

    7. Printer Found screen

      Clicking the Yes, install this printer. option button, and then clicking Next takes you to the Confirm Settings dialog box (Step h).

      Clicking the No, install a different printer. option button, and then clicking Next takes you to the Check Cable Connection dialog box (Step k).

      NOTE: If more than one HP LaserJet 1022 Series printer is installed on the network, a list will appear from which you can select the specific HP LaserJet 1022 Series printer that you want to connect to.
    8. Confirm Settings screen

      Click Next. (Takes you to the Start Copying Files dialog box - Step m).

      Clicking Change TCP/IP Settings takes you to the Confirm Changing Setting dialog box (Step I).

    9. Confirm Changing Setting screen

      Clicking Yes and then clicking Next takes you to the Set Network Protocol dialog box (Step j).

      Clicking No and then clicking Next takes you to the Start Copying Files dialog box (Step m).

    10. Set Network Protocol screen

      Clicking the Network Protocol drop-down menu displays a list of network protocols for you to choose from.

      Clicking Change Settings allows you to change the network settings.

      Next takes you to the Start Copying Files dialog box (Step m).

      NOTE: Use this screen to configure an unconfigured network card.
    11. Check Cable Connection screen

      Clicking the Search again option button, and then clicking Next searches the network again and then takes you to the Printer Found dialog box (Step g).

      Clicking the Specify a printer by address option button, and then clicking Next takes you to the Specify Printer dialog box (Step l).

    12. Specify Printer screen

      Entering any of the addresses and then clicking Next takes you to the Printer Found dialog box (Step g).

    13. Start Copying Files screen

      Clicking Next starts the installation process and takes you to the Installation Status dialog box (Step n).

    14. Installation Status screen

      NOTE: During the installation process, the status bar refreshes several times.
    15. USB Cable Connect screen

      Back returns you to the Start Copying Files dialog box (Step m).

    16. Finish screen

      The Register LaserJet 1020 series Online and Print Test Page check boxes are selected by default.

      Clicking Finish with the Register LaserJet 1020 series Online check box selected closes the Install wizard, opens your Web browser, and then takes you to the HP Web Registration Web site.

      Clicking Finish with the Print Test Page check box selected closes the Install wizard and prints a test page.

      Clearing both check boxes and clicking Finish closes the Install wizard.

    17. Registration screen

      Enter appropriate information.

    18. Exit Setup screen

      Yes cancels the print-driver installation.

      No returns you to the last open screen of the installer.

  4. If you are prompted to restart your computer, click Yes.

Set up Windows sharing (peer-to-peer networking)

NOTE: This section describes procedures for sharing a product using Microsoft Windows Sharing (peer-to-peer networking). Peer-to-peer networking is a feature of Microsoft operating systems, not of HP print drivers. If these procedures are not successful, or for more information about peer-to-peer networking procedures, contact Microsoft at the following Web site: http://www.microsoft.com Non-HP site

This section contains instructions for using Windows sharing to make the product available to network users when the product is directly connected to a host computer.

NOTE: Using Windows sharing, the person using the computer directly connected to the product can allow other users on the network to print to the product.

When the product is shared, install the printer drivers on all of the computers that you want to print to the product.

When you have set up the host computer to share your product, you must also configure the client computers. Perform the following steps at the computers of all other network users who want to print to the product.

Set up the host computer running Windows 98 SE, Windows Me, or Windows 2000

At the computer that is directly connected to the product, perform the following steps:

  1. Click Start, click Settings, and then click Printers.

  2. In the printer list, right-click the icon for your HP LaserJet 1022 Series printer, and then click Sharing.

    NOTE: If Sharing does not appear on the right-click menu, you must first enable printer sharing for Windows 98 SE or Windows Me. Follow these steps:
    1. Click Start, click Settings, and then click Control Panel.

    2. Double-click the Network icon.

    3. On the General tab, click File and Print Sharing.

    4. Click the I want to be able to allow others to print to my printers check box, and then click OK.

    5. Click OK again, and then close the Control Panel. If you are prompted to restart your computer, click Yes.

  3. On the Sharing tab, click the Share As option button, and then type a name for the product in the Share Name field. Click OK.

top

Set up the host computer running Windows XP

At the computer that is directly connected to the product, perform the following steps:

  1. Click Start, and then click Printers and Faxes.

  2. In the printer list, right-click the icon for your HP LaserJet 1022 Series printer, and then click Sharing.

  3. On the Sharing tab, click the Share this printer option button, and then type a name for the product in the Share Name field. Click OK.

  4. Click the Ports tab. Click to clear the Enable bidirectional support check box, and then click OK.

top

Set up client computers running Windows 98 SE, Windows Me, or Windows 2000

  1. Click Start, click Settings, and then click Printers.

  2. Double-click the Add Printer icon to open the Add Printer wizard.

  3. Click Next to start the wizard.

  4. Click the Network Printer option button, and then click Next.

  5. Type in the path and share name of the HP LaserJet 1022 Series printer to which you want to connect.

    - OR -

    Click Browse and navigate to find the HP LaserJet 1022 Series printer to which you want to connect.

    Click Next.

  6. Click the Yes or No option button when asked if you want to use this product as your default printer for Windows-based programs, and then click Next.

  7. Click Finish to complete the installation and close the Add Printer wizard.

    NOTE: You might need the product software CD to complete the printer driver installations.

top

Set up client computers running Windows XP

  1. Click Start, and then click Printers and Faxes.

  2. On the left-hand column, under Printer Tasks, click Add a printer to open the Add Printer wizard.

  3. Click Next to start the wizard.

  4. Click the A network printer or a printer attached to another computer option button, and then click Next.

  5. Type in the path and share name of the HP LaserJet 1022 Series printer to which you want to connect.

    - OR -

    Click Browse and navigate to find the HP LaserJet 1022 Series printer to which you want to connect.

    Click Next.

  6. Click the Yes or No option button when asked if you want to use this product as your default printer for Windows-based programs, and then click Next.

  7. Click Finish to complete the installation and close the Add Printer wizard.

top

top

top

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!