Print | Rate this content

HP ProCurve 2910al Switch Series - Specifications

HP ProCurve 2910al-24G Switch (J9145A)

Click here to view the physical specifications for the HP ProCurve 2910al-24G Switch .

Click here to view the environmental specifications for the HP ProCurve 2910al-24G Switch .

Click here to view the power specifications for the HP ProCurve 2910al-24G Switch .

Click here to view the technical specifications for the HP ProCurve 2910al-24G Switch .

Physical specifications for the HP ProCurve 2910al-24G Switch
Feature
Description
Dimensions(d)*(w)*(h)
36.58 x 44.2 x 4.39 cm (14.4 x 17.4x 1.73 in) (1U height)
Weight
4.95 kg (10.92 lb)
Mounting
Mounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-24G Switch
Feature
Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)

Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing

Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)

Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing

Altitude
  • up to 3 km (10,000 ft)

Acoustic
  • Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779

Power specifications for the HP ProCurve 2910al-24G Switch
Feature
Description
Voltage
  • 100-127/200-240 Vac

Current
  • 1.7/0.9 A

Idle power
  • 49 W

Power consumption
  • 82 W

Frequency
  • 50/60 Hz

Maximum heat dissipation
  • 295 kJ/hr (279 BTU/hr)

Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz

NOTE: Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Technical specifications for the HP ProCurve 2910al-24G Switch
Feature
Description
Processor
  • Dual ARM1156T2S @ 515 MHz

Memory
  • 4MB flash, 1GB flash ROM, 512MB SDRAM

  • packet buffer size: 6MB

Performance
Latency :
  • 1000Mb : < 2.9 µs (FIFO)

  • 10 Gbps : < 1.3 µs (FIFO)

Throughput :
  • up to 95 million pps (64-byte packets)

Switching capacity :
  • 128 Gbps

Routing table size :
  • 2000 entries

MAC address table size :
  • 16,000 entries

Ports
  • 20 auto-sensing 10/100/1000 ports :

    • IEEE 802.3 Type 10Base-T

    • IEEE 802.3u Type 100Base-TX

    • IEEE 802.3ab Type 1000Base-T

    Media Type :

    • Auto-MDIX

    • Duplex: 10Base-T/100Base-TX: half or full

    • 1000Base-T: full only

  • 4 dual-personality ports :

    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)
  • 1 RJ-45 serial console port

  • Supports a maximum of four 10-GbE ports, with optional module

Management
  • HP ProCurve Manager Plus

  • HP ProCurve Manager

  • Command-line interface

  • Web browser

  • Out-of-band management (serial RS-232C)

NOTE: When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

top

HP ProCurve 2910al-24G-PoE+ Switch (J9146A)

Click here to view the physical specifications for the HP ProCurve 2910al-24G-PoE+ Switch .

Click here to view the environmental specifications for the HP ProCurve 2910al-24G-PoE+ Switch .

Click here to view the power specifications for the HP ProCurve 2910al-24G-PoE+ Switch .

Click here to view the technical specifications for the HP ProCurve 2910al-24G-PoE+ Switch .

Physical specifications for the HP ProCurve 2910al-24G-PoE+ Switch
Feature
Description
Dimensions(d)*(w)*(h)
36.58 x 44.2 x 4.39 cm (14.4 x 17.4 x 1.73 in) (1U height)
Weight
5.6 kg (12.34 lb)
Mounting
Mounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-24G-PoE+ Switch
Feature
Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)

Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing

Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)

Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing

Altitude
  • up to 3 km (10,000 ft)

Acoustic
  • Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779

Power specifications for the HP ProCurve 2910al-24G-PoE+ Switch
Feature
Description
Voltage
  • 100-127/200-240 Vac

Current
  • 6.1/3.1 A

Idle power
  • 65 W

Power consumption
  • 490 W

Frequency
  • 50/60 Hz

Maximum heat dissipation
  • 472 kJ/hr (447 BTU/hr), max. using PoE+

Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz

NOTE: Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Technical specifications for the HP ProCurve 2910al-24G Switch
Feature
Description
Processor
  • Dual ARM1156T2S @ 515 MHz

Memory
  • 4MB flash ROM, 1GB flash, 512MB SDRAM

  • packet buffer size: 6MB

Performance
Latency :
  • 1000Mb : < 2.9 µs (FIFO)

  • 10 Gbps : < 1.3 µs (FIFO)

Throughput :
  • up to 95 million pps (64-byte packets)

Switching capacity :
  • 128 Gbps

Routing table size :
  • 2000 entries

MAC address table size :
  • 16,000 entries

Ports
  • 20 auto-sensing 10/100/1000 ports :

    • IEEE 802.3 Type 10Base-T

    • IEEE 802.3u Type 100Base-TX

    • IEEE 802.3ab Type 1000Base-T

    Media Type :

    • Auto-MDIX

    • Duplex: 10Base-T/100Base-TX: half or full

    • 1000Base-T: full only

  • 4 dual-personality ports :

    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)
  • 1 RJ-45 serial console port

  • Supports a maximum of four 10-GbE ports, with optional module

Management
  • HP ProCurve Manager Plus

  • HP ProCurve Manager

  • Command-line interface

  • Web browser

  • Out-of-band management (serial RS-232C)

NOTE: When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

top

HP ProCurve 2910al-48G Switch (J9147A)

Click here to view the physical specifications for the HP ProCurve 2910al-48G Switch .

Click here to view the environmental specifications for the HP ProCurve 2910al-48G Switch .

Click here to view the power specifications for the HP ProCurve 2910al-48G Switch .

Click here to view the technical specifications for the HP ProCurve 2910al-48G Switch .

Physical specifications for the HP ProCurve 2910al-48G Switch
Feature
Description
Dimensions(d)*(w)*(h)
36.58 x 44.25 x 4.4 cm (14.4 x 17.42 x 1.73 in) (1U height)
Weight
5.08 kg (11.2 lb)
Mounting
Mounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-48G Switch
Feature
Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)

Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing

Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)

Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing

Altitude
  • up to 3 km (10,000 ft)

Acoustic
  • Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779

Power specifications for the HP ProCurve 2910al-48G Switch
Feature
Description
Voltage
  • 100-127/200-240 Vac

Current
  • 2.1/1.1 A

Idle power
  • 64 W

Power consumption
  • 105 W

Frequency
  • 50/60 Hz

Maximum heat dissipation
  • 376 kJ/hr (356 BTU/hr)

Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz

NOTE: Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Technical specifications for the HP ProCurve 2910al-48G Switch
Feature
Description
Processor
  • Dual ARM1156T2S @ 515 MHz

Memory
  • 4MB flash, 1GB flash ROM, 512MB SDRAM

  • packet buffer size: 6MB

Performance
Latency :
  • 1000Mb : < 2.9 µs (FIFO)

  • 10 Gbps : < 1.3 µs (FIFO)

Throughput :
  • up to 131 million pps

Switching capacity :
  • 176 Gbps

Routing table size :
  • 2000 entries

MAC address table size :
  • 16,000 entries

Ports
  • 44 auto-sensing 10/100/1000 ports :

    • IEEE 802.3 Type 10Base-T

    • IEEE 802.3u Type 100Base-TX

    • IEEE 802.3ab Type 1000Base-T

    Media Type :

    • Auto-MDIX

    • Duplex: 10Base-T/100Base-TX: half or full

    • 1000Base-T: full only

  • 4 dual-personality ports :

    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)
  • 1 RJ-45 serial console port

  • Supports a maximum of four 10-GbE ports, with optional module

Management
  • HP ProCurve Manager Plus

  • HP ProCurve Manager

  • Command-line interface

  • Web browser

  • Out-of-band management (serial RS-232C)

NOTE: When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

top

HP ProCurve 2910al-48G-PoE+ Switch (J9148A)

Click here to view the physical specifications for the HP ProCurve 2910al-48G-PoE+ Switch .

Click here to view the environmental specifications for the HP ProCurve 2910al-48G-PoE+ Switch .

Click here to view the power specifications for the HP ProCurve 2910al-48G-PoE+ Switch .

Click here to view the technical specifications for the HP ProCurve 2910al-48G-PoE+ Switch .

Physical specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature
Description
Dimensions(d)*(w)*(h)
36.58 x 44.25 x 4.39 cm (14.4 x 17.42x 1.73 in) (1U height)
Weight
5.88 kg (12.96 lb)
Mounting
Mounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature
Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)

Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing

Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)

Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing

Altitude
  • up to 3 km (10,000 ft)

Acoustic
  • Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779

Power specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature
Description
Voltage
  • 100-127/200-240 Vac

Current
  • 6.4/3.2 A

Idle power
  • 89 W

Power consumption
  • 556 W

Frequency
  • 50/60 Hz

Maximum heat dissipation
  • 704 kJ/hr (667 BTU/hr)

Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz

NOTE: Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Technical specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature
Description
Processor
  • Dual ARM1156T2S @ 515 MHz

Memory
  • 4MB flash ROM, 1GB flash, 512MB SDRAM

  • packet buffer size: 6MB

Performance
Latency :
  • 1000Mb : < 2.9 µs (FIFO)

  • 10 Gbps : < 1.3 µs (FIFO)

Throughput :
  • up to 131 million pps

Switching capacity :
  • 176 Gbps

Routing table size :
  • 2000 entries

MAC address table size :
  • 16,000 entries

Ports
  • 44 auto-sensing 10/100/1000 ports :

    • IEEE 802.3 Type 10Base-T

    • IEEE 802.3u Type 100Base-TX

    • IEEE 802.3ab Type 1000Base-T

    Media Type :

    • Auto-MDIX

    • Duplex: 10Base-T/100Base-TX: half or full

    • 1000Base-T: full only

  • 4 dual-personality ports :

    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)
  • 1 RJ-45 serial console port

  • Supports a maximum of four 10-GbE ports, with optional module

Management
  • HP ProCurve Manager Plus

  • HP ProCurve Manager

  • Command-line interface

  • Web browser

  • Out-of-band management (serial RS-232C)

NOTE: When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

top

Safety and emission certificates

Feature
Description
Safety
  • EN 60950/IEC 60950

  • CAN/CSA 22.2 No. 60950

  • EN 60825

  • UL 60950

Emissions
  • FCC part 15 Class A

  • EN 55022/CISPR-22 Class A

  • VCCI Class A

Immunity
EN :
  • EN 55024, CISPR 24

ESD :
  • IEC 61000-4-2; 4 kV CD, 8 kV AD

Radiated :
  • IEC 61000-4-3; 3 V/m

EFT/Burst :
  • IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)

Surge :
  • IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC

Conducted :
  • IEC 61000-4-6; 3 V

Power frequency magnetic field :
  • IEC 61000-4-8; 1 A/m

Voltage dips and interruptions :
  • IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods

Harmonics :
  • IEC 61000-3-2

Flicker :
  • IEC 61000-3-3

top

Standards and protocols

Feature
Description
Device management
  • RFC 1591 DNS (client)

  • HTML and telnet management

General protocols
  • IEEE 802.1D MAC Bridges

  • IEEE 802.1p Priority

  • IEEE 802.1Q VLANs

  • IEEE 802.1s Multiple Spanning Trees

  • IEEE 802.1v VLAN classification by Protocol and Port

  • IEEE 802.1w Rapid Reconfiguration of Spanning Tree

  • IEEE 802.3ad Link Aggregation Control Protocol (LACP)

  • IEEE 802.3x Flow Control

  • RFC 768 UDP

  • RFC 783 TFTP Protocol (revision 2)

  • RFC 792 ICMP

  • RFC 793 TCP

  • RFC 826 ARP

  • RFC 854 TELNET

  • RFC 868 Time Protocol

  • RFC 951 BOOTP

  • RFC 1058 RIPv1

  • RFC 1350 TFTP Protocol (revision 2)

  • RFC 2030 Simple Network Time Protocol (SNTP) v4

  • RFC 2131 DHCP

  • RFC 2453 RIPv2

  • RFC 3046 DHCP Relay Agent Information Option

IP multicast
  • RFC 3376 IGMPv3 (host joins only)

IPv6
  • RFC 1981 IPv6 Path MTU Discovery

  • RFC 2460 IPv6 Specification

  • RFC 2710 Multicast Listener Discovery (MLD) for IPv6

  • RFC 2925 Remote Operations MIB (Ping only)

  • RFC 3019 MLDv1 MIB

  • RFC 3315 DHCPv6 (client only)

  • RFC 3513 IPv6 Addressing Architecture

  • RFC 3596 DNS Extension for IPv6

  • RFC 3810 MLDv2 (host joins only)

  • RFC 4022 MIB for TCP

  • RFC 4113 MIB for UDP

  • RFC 4251 SSHv6 Architecture

  • RFC 4252 SSHv6 Authentication

  • RFC 4253 SSHv6 Transport Layer

  • RFC 4254 SSHv6 Connection

  • RFC 4293 MIB for IP

  • RFC 4419 Key Exchange for SSH

  • RFC 4443 ICMPv6

  • RFC 4541 IGMP & MLD Snooping Switch

  • RFC 4861 IPv6 Neighbor Discovery

  • RFC 4862 IPv6 Stateless Address Auto-configuration

MIBs
  • RFC 1213 MIB II

  • RFC 1493 Bridge MIB

  • RFC 1724 RIPv2 MIB

  • RFC 2021 RMONv2 MIB

  • RFC 2613 SMON MIB

  • RFC 2618 RADIUS Client MIB

  • RFC 2620 RADIUS Accounting MIB

  • RFC 2665 Ethernet-Like-MIB

  • RFC 2668 802.3 MAU MIB

  • RFC 2674 802.1p and IEEE 802.1Q Bridge MIB

  • RFC 2737 Entity MIB (Version 2)

  • RFC 2863 The Interfaces Group MIB

Network management
  • IEEE 802.1AB Link Layer Discovery Protocol (LLDP)

  • RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)

  • RFC 3176 sFlow

  • ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED)

  • SNMPv1/v2c/v3

  • XRMON

QoS/Cos
  • RFC 2474 DiffServ Precedence, including 8 queues/port

  • RFC 2597 DiffServ Assured Forwarding (AF)

  • RFC 2598 DiffServ Expedited Forwarding (EF)

  • Ingress Rate Limiting

Security
  • IEEE 802.1X Port Based Network Access Control

  • RFC 1492 TACACS+

  • RFC 2138 RADIUS Authentication

  • RFC 2866 RADIUS Accounting

  • Secure Sockets Layer (SSL)

top

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!