Print | Rate this content

HP Deskjet Ink Advantage 2060 (K110a) All-in-One Printer - Setting up the All-in-One (Hardware)

Introduction

This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.

This document includes the following steps to set up the product:

  • Unpack the All-in-One

  • Check the contents of the box

  • Connect the power cord and adapter

  • Turn on power

  • Load plain paper

  • Install the cartridges

  • Align the cartridges

Setting up the All-in-One

Follow these steps in order.

CAUTION: Do NOT connect the USB cable now. If you need a USB cable to connect the product to the computer, you will be prompted to connect it at the correct time during software installation.

Step one: Unpack the All-in-One

  1. Remove the tape and cardboard from the outside of the product.

    Figure 1: Remove tape from the outside of the product

    Graphic: Remove tape from the outside of the product.
  2. Open the front access door, open the cartridge access door, and then remove the tape and cardboard from the inside of the product.

    Figure 2: Remove the tape and cardboard from inside the product

    Graphic: Remove the tape and cardboard from inside the product
  3. Close the cartridge access door.

    Figure 3: Close the cartridge access door

    Graphic: Close the cartridge access door
  4. Raise the input tray.

    Figure 4: Raise the input tray

    Graphic: Raise the input tray
  5. Pull out the tray extender.

    Figure 5: Pull out the tray extender

    Graphic: Pull out the tray extender

Step two: Check the contents of the box

The contents might vary by country/region. See the packaging for a list of items shipped in the box.

Step three: Connect the power cord and adapter

  1. Connect the power cord to the rear of the product.

    Figure 6: Connect the power cord to the rear of the product

    Graphic: Connect the power cord to the rear of the product
  2. Connect the power cord to the power supply, and then into a power outlet in the wall.

    Figure 7: Connect the power cord to the power supply, and then into a power outlet in the wall

    Graphic: Connect the power cord to the power supply, and then into a power outlet in the wall

Step four: Turn on power

Press the Power button () to turn the product on.

Figure 8: Turn on the product

Graphic: Turn on the product

Step five: Load plain paper

Get Macromedia Flash now.
To view the following movie you must have the Flash Player installed on your system.
Download Flash Now Non-HP site

  1. Slide the paper width guide to its outermost position.

  2. Load a stack of 216 x 279 mm (8.5 x 11 in) plain paper into the paper tray, print-side down. Slide the stack of paper in until it stops.

  3. Slide the paper width guide snugly against the paper.

    Figure 9: Load paper, and then adjust the paper width guide

    Graphic: Load paper, and then adjust the paper width guide

Step six: Install the cartridges

  1. Press the Power button () to turn on the product, if it is not already turned on. Wait until the product is idle and silent before continuing.

  2. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing.

    Figure 10: Open the cartridge access door

    Graphic: Open the cartridge access door
  3. Remove the new cartridge from its packaging, and then carefully pull the pink pull tab to remove the plastic tape.

    CAUTION: Do not touch the copper-colored contacts or ink nozzles. Also, do not re-tape the cartridges. Doing so can result in clogs, ink failure, and bad electrical connections.

    Figure 11: Remove the plastic tape

    Illustration of removing the tape from the new cartridge
  4. Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot.

    • The tri-color cartridge () goes in the slot on the left.

    • The black cartridge () goes in the slot on the right.

    Figure 12: Insert the cartridge into its slot

    Graphic of installing a cartridge
  5. Push the cartridge forward into its slot until it snaps into place.

    Figure 13: Snap the cartridge into place

    Graphic: Snap the cartridge into place
  6. Repeat these steps to insert the other cartridge.

  7. Close the cartridge access door.

    Figure 14: Close the cartridge access door

    Graphic: Close the cartridge access door
  8. Wait about 30 seconds for the alignment page to automatically print.

    Figure 15: The alignment page prints automatically after 30 seconds

    Graphic: The alignment page prints automatically after 30 seconds

Step seven: Align the cartridges

  1. Lift the scanner lid.

  2. Place the alignment page with the printed-side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page.

    Figure 16: Place the alignment page on the scanner glass

    Graphic: Place the alignment page on the scanner glass
  3. Close the scanner lid.

  4. Press the Start Copy Black button () to begin the scan. The product automatically aligns the cartridges.

  5. Wait until the Power light () stops blinking, which indicates that the cartridge alignment is complete.

  6. Recycle or discard the alignment page.

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!